Einzelheiten zu den Produkten
|
Tested Fluke 9640A Series RF Reference Source multi product oscilloscope calibrator
| Markenbezeichnung: | Fluke |
| Modellnummer: | Fluke 9640a |
| MOQ: | 1 Set |
| Preis: | Verhandlungsfähig |
| Zahlungsbedingungen: | T/t |
Fluke 9640A RF Reference Source
,multi product oscilloscope calibrator
,Series RF calibrator with warranty
Tested Fluke 9640A Series RF Reference Source multi product oscilloscope calibrator
Description of Fluke 9640A RF Reference Source
The 9640A Series is an RF reference that takes the central role and typically halves the cost of a high capability RF calibration system. Its unique features and performance enable it to replace up to four signal sources (from audio/function generators to RF signal and low phase noise sources), power meters and power sensors, step attenuators, filters, pads, couplers, and also a frequency counter with the 9600FC integrated counter option. For many spectrum analyzer models operating below 4 GHz, only the 9640A Series is required to perform their entire calibration.
The 9640A Series performs more than 80 percent of all the tests required during high performance spectrum analyzer calibration. For workload with frequency requirements beyond 4 GHz, an existing RF and microwave source can be used alongside the 9640A rf reference to address the few remaining higher frequency test points all controlled by MET/CAL software.
The features of the 9640A Series provide many benefits in spectrum analyzer calibration. They also make the 9640A ideal for other workload, including RF millivoltmeters, signal level meters, modulation analyzers, receivers, counter/timers and attenuator calibration. Reducing the number of instruments in a calibration system brings many benefits. Metrology is simpler with fewer error sources and uncertainty contributions to consider. System support costs are reduced, as there are fewer instruments to calibrate and maintain. A smaller, more compact and robust system with a dependable rf reference is also a practical onsite calibration solution with lower transport costs.
The 9640A models are designed to match or exceed the performance and functionality of the HP3335A and HP8662/3A in calibration systems. With HP3335A GPIB command emulation as standard in both 9640A models and optional HP8662/3A emulation in the 9640A-LPNX, replacing these popular but obsolete and difficult-to-maintain products becomes just a plug-and-play substitution. HP8662/3A GPIB command emulation is installed on the 9640A-LPNX as "try before you buy" temporary license for convenient and thorough compatibility testing.
| Summary specifications | ||
| Frequency specifications | Level specifications (50 Ω output, see extended specifications for 75 Ω) |
|
| Range | 1 mHz to 4 GHz | -130 to +24 dBm to 125 MHz, 14 dBm at 4 GHz (leveled) |
| Resolution | 10 uHz | 0.001 dB |
| Accuracy | 0.05 ppm + 5 uHz | Down to -48 dBm 0.03 dB to 100 kHz, 0.05 dB to 128 MHz, 0.5 dB at 4 GHz 10 MHz to 128 MHz 0.05 dB to -48 dBm, 0.1 dB to -84 dBm, 0.7 dB at -130 dBm |
| Attenuation | 0.02 dB to 55 dB, 0.15 dB at 110 dB | |
| VSWR | ≤500 MHz: ≤1.1, ≤1 GHz: 1.2, ≤3 GHz: 1.3, ≤4 GHz: 1.4 |
|
| Harmonics and spurious | –60 dBc harmonics, –70 dBc spurious to 1 GHz | |
| Phase noise at 1 GHz | 9640A: –122 dBc/Hz, typical, at 10 kHz offset 9640A-LPNX: –138 dBc/Hz, typical, at 5 kHz to 100 kHz offset |
|
| Modulation | AM, FM, PM, internal and external. Frequency pull and external leveling. | |
| Frequency sweep | 1 mHz to 4 GHz. Linear or Logarithmic. Stop-Start or Center-Span. | |
| Frequency counter | Optional internal 50 MHz frequency counter | |
| Temperature | Operating: 0 °C to 50 °C, 23 °C ± 5 °C for specified performance Storage: -20 °C to +70 °C |
|
| Standard interfaces | IEEE488.2 (GPIB) | |
| GPIB command emulation | 9640A, 9640A-LPNX: HP3335 9640A-LPNX + Opt 8662/8663 GPIB: HP3335, HP8662A, HP8663A |
|
| Calibration documentation | 17025 accredited report of calibration included | |
| Dimensions (HxWxD) | 146 mm x 433 mm x and 533 mm (5.8 in x 17.0 in x 21.0 in) Industry-standard 19 in (483 mm) rack mounting when fitted with Y9600 rack mounting kit | |
| Weight | 18 kg (40 lbs) | |
FAQ:
1.Can you ship order to Canada or Australia ?
Yes,we can .We send orders worldwide .
2. What delivery method do you use ? and delivery time ?
We can ship by EMS,DHL,FedEx,UPS,TNT with tracking number. Usual delivery time is 4-7 workdays.
3. What is your payment term?
100% T/T payment before shipment.
4. How can I ask any other question ?
You can contact us online or leave us messages below .
Video
Video
Video
